FRANCESCO LECCESE

Associate Professor

University of Pisa
Country flagItaly

Research Interests

ApplyKite TwinLearns as you apply

Make your next move.

Prepare your application

Review drafts before you send them.

Explore related searches

Articles (12)

Year:

2026

The perceived acoustic comfort on board modern yachts has recently been the subject of specific attention by the most important classification societies, which have issued new guidelines and regulations for the evaluation of noise and vibrations. The evaluation of the acoustic insulation performance of the internal partitions of yachts is, therefore, a very current topic. The estimation of the acoustic performance of internal partitions can be very complex; on the one hand, on-board measurements can be extremely difficult, but on the other hand, manual or software calculation is extremely complex or potentially affected by non-negligible errors, which is also due to the high amount of highly detailed information required. This paper explores the possibility of using simplified models, commonly used in building construction, to determine the acoustic insulation of the internal partitions of yachts in the design phase, without having to resort, even from the beginning, to very advanced calculation tools such as those based on the Finite Elements Method or Statistical Energy Analysis. Using a 44 m yacht as a case study, this paper presents the results of a series of acoustic simulations of single partitions and compares them with the results of an on-board measurement campaign. From the comparison of the obtained results, it was possible to state that the simulations of single partitions (therefore, those not of the whole vessel) can be useful in the design phase to verify compliance with the acoustic requirements requested by the classification societies. Considering that the propagation of sound and vibrations through the structures is a determining factor for the correct acoustic design of the vessel and therefore for the achievement of adequate levels of acoustic comfort, the analysis with simplified models (which consider the single partition) can be extremely useful in the preliminary phase of the design process. Subsequently, starting from the data acquired in the first simulation phase, it is possible to proceed with more complex simulations of specific situations and of the whole vessel.

Year:

2025

Managing complex and large-scale building facilities requires reliable, easily interpretable, and computationally efficient models. Considering the electrical-circuit analogy, lumped-parameter resistance–capacitance (RC) thermal models have emerged as both simulation surrogates and advanced tools for energy management. This review synthesizes recent uses of RC models for building energy management in large facilities and aggregates. A systematic review of the most recent international literature, based on the analysis of 70 peer-reviewed articles, led to the classification of three main areas: (i) the physics and modeling potential of RC models; (ii) the methods for automation, calibration, and scalability; and (iii) applications in model predictive control (MPC), energy flexibility, and digital twins (DTs). The results show that these models achieve an efficient balance between accuracy and simplicity, allowing for real-time deployment in embedded control systems and building-automation platforms. In complex and large-scale situations, a growing integration with machine learning (ML) techniques, semantic frameworks, and stochastic methods within virtual environments is evident. Nonetheless, challenges persist regarding the standardization of performance metrics, input data quality, and real-scale validation. This review provides essential and up-to-date guidance for developing interoperable solutions for complex building energy systems, supporting integrated management across district, urban, and community levels for the future.

Year:

2025

Prefabricated temporary buildings are a promising solution for post-disaster scenarios for their modularity, sustainability and transportation advantages. However, their low thermal mass building envelope shows a fast response to heat flux excitations. This leads to the risk of not meeting the occupant comfort and HVAC energy-saving requirements. The literature shows different measures implementable in opaque surfaces, like vacuum insulation panels (VIPs), phase change materials (PCMs) and switchable coatings, and in transparent surfaces (switchable glazing) to mitigate thermal issues, like overheating, while preserving the limited available internal space. This paper investigates the energy and overheating performance of the mentioned interventions by using building performance simulation tools to assess their effectiveness. The optimization also looks at the transportation flexibility of each intervention to better support the decision maker for manufacturing innovative temporary units. The most energy-efficient measures turn to be VIPs as a better energy solution for winter and PCMs as a better thermal comfort solution for summer.

Year:

2024

Year:

2023

Year:

2023

Year:

2022

Year:

2022

Year:

2020

Year:

2020

Year:

2020

Year:

2020

Collaborators (6)

Umberto Desideri

Full Professor

University of Pisa

ITALY
View details

Giacomo Salvadori

Professor (Associate)

University of Pisa

ITALY
View details

Francesca Di Puccio

Associate Professor

University of Pisa

ITALY
View details

Jérôme Henri Kämpf

Senior Research Scientist

Idiap Research Institute

SWITZERLAND
View details

marco beccali

Full Professor

Università degli Studi di Palermo

ITALY
View details

Fabio Fantozzi

Prof

University of Pisa

ITALY
View details