Grzegorz Dercz

This paper presents the results of tribological tests on WE43 and WE54 magnesium alloys with rare earth metals performed in linear reciprocating motion for four different material couples (AISI 316-L steel, silicon nitride—Si3N4, WC tungsten carbide, and zirconium dioxide—ZrO2). Additionally, magnesium alloys were subjected to a complex heat treatment consisting of precipitation hardening combined with a deep cryogenic treatment. The study presents the effect of deep cryogenic treatment combined with precipitation hardening on the tribological properties of WE43 and WE54 alloys. Tribological tests revealed the most advantageous results for the magnesium alloy—AISI 316-L steel friction node. For both alloys tested after heat treatment, a nearly 2-fold reduction in specific wear rate has been achieved. Furthermore, microscopic examinations of the wear track areas and wear products were performed, and the wear mechanisms and types of wear products occurring in linear reciprocating friction were determined. Wear measurements were taken using the 3D profilometric method and compared with the results obtained from calculations performed in accordance with ASTM G133 and ASTM D7755, which were modified to improve the accuracy of the calculation results (the number of measured profiles was increased from four to eight). Appropriately selected calculation methods allow for obtaining reliable tribological test results and enabling the verification of both the most advantageous heat treatment variant and material couple, which results in an increase in the durability of the tested alloys.

The purpose of the present study was to learn the morphological, structural, ferroelectric, dielectric, electromechanical, magnetoelectric, and magnetic properties, and DC conductivity of BaTiO3-Ni0.64Zn0.36Fe2O4 (BT-F) multiferroic composites compacted via the free sintering method. The influence of the ferrite content in ceramic composite materials on the functional properties is investigated and discussed. X-ray diffraction studies confirmed the presence of two main phases of the composite, with strong reflections originating from BaTiO3 and weak peaks originating from nickel-zinc ferrite. BT-F ceramic composites have been shown to exhibit multiferroism at room temperature. All studied compositions have high permittivity values and low dielectric loss, while the ferroelectric properties of the BT component are maintained at a high level. On the other hand, magnetic properties depend on the amount of the ferrite phase and are the strongest for the composition with 15 wt.% of F (magnetization at RT is 4.12 emu/g). The magnetoelectric coupling between BT and F phases confirmed by the lock-in technique is the largest for 15 wt.% ferrite. In the present work, the process conditions of the free sintering method for obtaining BT-F multiferroic composite with good electrical and magnetic properties (in one material) were optimized. An improved set of multifunctional properties allows the expansion of the possibilities of using multiferroic composites in microelectronics.

This study demonstrates the impact of two sintering techniques on the fundamental properties of doped PZT-type ceramic materials (with Mn4+, Sb3+, Gd3+, and W6+), with the general chemical formula Pb(Zr0.49Ti0.51)0.94Mn0.021Sb0.016Gd0.012W0.012O3. The synthesis of ceramic powders was carried out through the calcination method. Two different methods were used in the final sintering process: (i) pressureless sintering (PS) and (ii) hot pressing (HP). The PZT-type ceramics were subjected to electrophysical measurements, encompassing various analyses such as X-ray diffraction (XRD), microstructure (scanning electron microscopy (SEM)), ferroelectric and dielectric properties, and DC electrical conductivity. The analysis of the crystal structure at room temperature showed that the material belongs to the perovskite structure from the tetragonal phase (P4mm space group) without foreign phases. Both sintering methods ensure obtaining the material with appropriate dielectric and ferroelectric parameters, and the tests carried out verified that the ceramic materials have a diverse range of parameters appropriate for use in micromechatronic and microelectronic applications. The obtained ceramic material has high permittivity values, low dielectric loss tangent values, and high resistance. At room temperature, the ceramic samples’ P-E hysteresis loops do not saturate at a field of 3.5 kV/mm (Pm maximum polarization is in the range from 12.24 to 13.47 μC/cm2). However, at higher temperatures, the P-E hysteresis loops become highly saturated, and, at 110 °C, the Pm maximum polarization values are in the range from 28.02 to 30.83 μC/cm2.