Lorella Ceschini

The combination of precipitation-hardening stainless steels (PH-SS) and laser powder bed fusion (LPBF) enables the manufacturing of tools for plastic injection moulding with optimised geometry and conformal cooling channels, with potential benefits in terms of productivity, part quality, and tool duration. Moreover, the suitability of LPBF-manufactured PH-SS in the as-built (AB) condition to be age-hardened through a direct aging (DA) treatment enables a great heat treatment simplification with respect to the traditional solution annealing and aging treatment (SA). However, plastic injection moulding tools experience severe thermal cycles during their service, which can lead to over-aging of PH-SS and thus shorten tool life. Therefore, proper thermal stability is required to ensure adequate tool life and reliability. The aim of the present work is to investigate the aging and over-aging behaviour of a commercially available PH-SS (AMPO M789) manufactured by LPBF in the AB condition and after a solution-annealing treatment in order to evaluate the effect of the heat treatment condition on the microstructure and the aging and over-aging response, aiming at assessing its feasibility for plastic injection moulding applications. The AB microstructure features melt pool borders, oriented martensite grains, and a cellular solidification sub-structure, and was retained during aging and over-aging. On the other hand, a homogeneous and isotropic martensite structure was present after solution annealing and quenching, with no melt pool borders, cellular structure, or oriented grains. The results indicate no significant difference between AB and solution-annealed and quenched specimens in terms of aging and over-aging behaviour and peak hardness (in the range 580–600 HV), despite the considerably different microstructures. Over-aging was attributed to both the coarsening of strengthening precipitates and martensite-to-austenite reversion (up to ~11 vol.%) upon prolonged exposure to high temperature. Based on the results, guidelines to aid the selection of the most suitable heat treatment procedure are proposed.

Microstructure and tensile properties of a hot work tool steel manufactured via laser powder bed fusion (LPBF) were investigated. Specimens were built under two different orientations and subjected to two quenching and tempering heat treatments, featuring different austenitizing and tempering temperatures and the eventual presence of a sub‐zero step. Microstructural analyses revealed a homogeneous tempered martensite structure after both heat treatments, with the only distinction of a higher alloying segregation at a sub micrometric scale length in samples subjected to the highest tempering temperatures. Hardness and tensile tests indicated a negligible effect of building orientation on mechanical properties, but a significant influence of heat treatment parameters. The treatment featuring the lower tempering temperatures and the sub‐zero step resulted in higher hardness, tensile strength, and elongation, attributed to a lower martensite tempering and alloying segregation. Tensile fracture occurred via crack initiation and unstable propagation from large LPBF defects in all the investigated conditions.

The AlSi10Mg alloy produced by laser-based powder bed fusion (L-PBF) is widely used to produce high-value-added structural parts subjected to cyclic mechanical loads at high temperatures. The paper aims to widen the knowledge of the room- and high-temperature (200 °C) fatigue behavior of the L-PBF AlSi10Mg alloy by analyzing the fully reversed rotating bending test results on mechanically polished specimens. Two heat-treated conditions are analyzed: T5 (direct artificial aging: 4 h at 160 °C) and novel T6R (rapid solution: 10 min at 510 °C, artificial aging: 6 h at 160 °C). The study highlights that (i) the T6R alloy is characterized by higher fatigue strength at room (108 MPa) and high temperatures (92 MPa) than the T5 alloy (92 and 78 MPa, respectively); (ii) thermal exposure at 200 °C up to 17 h does not introduce macroscopical microstructural variation; (iii) fracture surfaces of the room- and high-temperature-tested specimens show comparable crack initiation, mostly from sub-superficial gas and keyhole pores, and failure propagation mechanisms. In conclusion, the L-PBF AlSi10Mg alloy offers good cyclic mechanical performances under various operating conditions, especially for the T6R alloy, and could be considered for structural components operating at temperatures up to 200 °C.