Yasushi Endo

Has grant

Professor

Tohoku University
Country flagJapan

Research Interests

ApplyKite TwinLearns as you apply

Make your next move.

Prepare your application

Review drafts before you send them.

Explore related searches

Recent Grants

Grant: Close

Study on the static and dynamic magnetic properties of arrayed amorphous metal magnetic particles with the submicron sizes

Open Date: 2019-06-28

Close Date: 2021-03-31

Grant: Close

電界制御反強磁性スピンダイナミクス

Open Date: 2019-04-01

Close Date: 2022-03-31

Grant: Close

Voltage controlled spin-wave resonance in magnetic 2D structures

Open Date: 2017-04-26

Close Date: 2019-03-31

Grant: Close

Study on the magnetization dynamics of ultra-thin magnetic films using a newly proposed high-frequency magnetization measurement technique

Open Date: 2017-04-01

Close Date: 2020-03-31

Grant: Close

Spin dynamics of epitaxial ferromagnetic metal film on insulating layer

Open Date: 2014-04-01

Close Date: 2016-03-31

Articles (8)

L10-ordered FePd epitaxial films with a nominal thickness of 5 nm were grown by r.f. magnetron sputtering on the SrTiO3 (001) single crystal substrates by a two-step heating method. A subtle 50 K change in the first-heating temperature of a two-step process drastically alters the morphological trajectory of L10-FePd films, switching among three regimes: (i) Frank–van der Merwe (FM — atomically flat), (ii) Solid-state dewetting (SSD — square holes), and (iii) Stranski-Krastanov (SK — 3D grains). (i) [FM mode]Almost no lattice disturbance in the in-plane direction, and perfect constraint by tensile strain from the SrTiO3 substrate was achieved. (ii) [SSD mode] Square holes penetrating to the SrTiO3 substrate were formed, and sides of the square were grown along the or of the SrTiO3 substrate. According to first-principles calculations, a large difference in surface free energy between L10-FePd and the SrTiO3 substrate is predicted. This difference in surface free energy is the minimum necessary condition for SSD to occur. The trigger for SSD is small holes/voids formed during the 1st heating process in the two-step heating process. (iii) [SK mode] Grains grew 3-dimensionally, which is typically categorized by the SK growth mode. Note that the 1st heating temperature of the two-step heating process significantly changed the morphological trajectory, even though the 2nd heating temperature of 600°C was significantly higher than that of the 1st growth temperature. The SSD reduced the substrate restraint, resulting in the highest degree of L10-ordering (SL10 = 0.99) and the highest perpendicular magnetic anisotropy (PMA = 1.33MJ/m3).

Year:

2026

This paper reports the core loss of soft magnetic composite toroidal cores consisting of submicron-sized amorphous Fe–B particles with spherical shape synthesized by an aqueous reduction reaction method. The core loss of Fe–B composite cores was as low as 0.0015 J/m3 in the frequency range of 10 kHz to 4 MHz at a maximum magnetic flux density Bm of 1 mT, meaning that the eddy current loss can be suppressed. This result can be derived from a combination of the reduction of the particle size, amorphous structure and their relatively higher resistivity. In contrast to Fe–B particles, the toroidal core consisting of the commercial carbonyl iron particles showed the increase of core loss at the frequency more than 200 kHz, which may be attributed to the increment of eddy current loss originating from their relatively larger particle size and decrement of resistivity induced by particle coarse after compaction. Therefore, these results suggest that submicron-sized amorphous Fe–B particles is one of the candidate materials for the next-generation magnetic passive components in the frequency range of MHz.

Year:

2026

This article reports the influence of annealing treatment on magnetic properties of submicron sized amorphous Fe–Co–B particles synthesized by an aqueous solution reduction method. The structure of Fe–Co–B particles was mainly amorphous for the annealing temperature less than 250 °C, a precipitation of bcc phase from the amorphous at the annealing temperature of 300 °C, and further transferred to the bcc structure at the annealing temperature above 350 °C. Their static magnetic properties such as saturation magnetization and coercivity were improved markedly at lower annealing temperatures, compared to those of as-synthesized particles, due to the enhancement of short-range order and the relaxation of internal stress. The imaginary part of complex permeability was maintained as almost zero in the frequency range of 0.3–0.5 GHz, meaning the suppression of eddy current. Therefore, these results suggest that the appropriate annealing treatment for submicron sized amorphous Fe–Co–B particles has considerable potential to develop the constituent materials of the next-generation magnetic elements.

Year:

2026

The influence of annealing temperature on the structure and magnetic properties of 10 μm-thick Fe-1, 2, and 3 wt. %Si foils was investigated. The coercivity of each foil decreased and its relative permeability increased as the annealing temperature increased, meaning the improvement of soft magnetic properties of these foils. The core loss of each foil at 100 kHz under a maximum magnetic flux density of 500 mT showed a decrease intendency with the increase of annealing temperature, owing to the suppression of the hysteresis loss by grain growth after annealing. Furthermore, from the loss separation of each foil, it was found that the eddy current loss slightly decreased and excess loss tend to increase with the increase of annealing temperature regardless of Si content. Therefore, these results suggest that an appropriate annealing temperature can improve the magnetic properties and core loss of ultra-thin Fe–Si foils, making them applicable as magnetic materials for next generation passive components in the frequency range up to several hundreds kHz.

Year:

2026

We report the induction of large in-plane uniaxial magnetic anisotropy for the CoFeB-based thin films by post-annealing under the magnetic field application. The comprehensive study reveals the influence of CoFeB composition and Pt addition to CoFeB on the induced magnetic anisotropy by magnetic field annealing. The addition of Pt to a CoFeB film significantly enhances the effect of magnetic field annealing, and as a result, the CoFeB–Pt films exhibit the in-plane uniaxial magnetic anisotropy energies that are one order of magnitude larger than the pristine CoFeB films. In order to understand the mechanism of magnetic anisotropy induction by post-annealing, we carried out the magnetostriction measurement for the CoFeB-based thin films. The correlation between the induced magnetic anisotropy and magnetoelastic properties is discussed.

Year:

2025

This paper reports the influence of rare-earth (RE) doping on static and dynamic magnetic properties of 50-nm-thick Fe-Ga films grown on a glass substrate. With the addition of RE elements, the magnetic softness of Fe-Ga films improved at higher RE content, which might be attributed to the induction of in-plane uniaxial anisotropy by RE doping. As for the dynamic properties of Fe-Ga-RE films, an overall increased effective in-plane damping constant (α//,eff) were observed as the increase of RE content, except for a decreased α//,eff from 0.0228 to 0.0151 at low RE contents. These results suggest that the addition of RE could induce tunable magnetic properties in Fe-Ga films, making resultant Fe-Ga-RE films as one of the promising candidates for the sensing applications and high frequency microwave magnetic devices.

Year:

2025

Fe-Ni cores are excellent candidates for switching regulator inductors, transformers, reactors and in-line noise filters. Herein the influence of the phenol binder content on the microstructure and magnetic properties of Fe-50 wt% Ni powder cores in the high frequency range is investigated. Regardless of the binder content, all cores form a disordered A1 phase. The saturation magnetization (4πMs) and initial permeability increase as the binder content decreases. The core with a binder content of 0.5 wt% shows a relatively high 4πMs of 1.38 T and the highest permeability value of 70.9. Moreover, the total core loss (Pcv) with frequency ranges from 5 kHz to 1 MHz under a magnetic flux density of 10 mT depending on the binder content. A binder content of 3.0 wt% significantly reduces Pcv in the high frequency range above 100 kHz. At a frequency of 500 kHz, the Pcv values are 154.9, 128.7, and 133.8 kW/m3 for the cores with binder contents of 0.3, 0.5, and 1.0 wt%, respectively, but the value drastically decreases to 60.5 kW/m3 for a binder content of 3.0 wt%. Thus, the binder, which acts as an insulator layer between particles, affects the eddy current and consequently, Pcv. These results demonstrate that Fe-Ni powder cores exhibit excellent soft magnetic properties at various frequencies and suggest that a binder content of 3.0 wt% may realize optimal properties for future high frequency applications.

Year:

2024

Fe-based amorphous powder cores of Fe–Si–B–Cr–C magnetic powder and phenolic binder were fabricated, and the effects of annealing and compaction pressure on the soft magnetic properties and core loss were investigated. The formation of Fe–B and α-Fe (Si) phases was confirmed at the annealing temperature above 773 K. The density gradually increased from 5.3 to 5.5 g/cm3 as annealing temperature increased, resulting in the saturation magnetization 4πMs increased to 1.0 T at 773 K. The effect of compaction pressure was studied by using samples annealed at 723 K. Both the density and 4πMs enhanced with compaction pressure from 980 to 1960 MPa. The real part of permeability µ’ remained constant for the frequency up to 2 MHz. The initial value of µ’ increased from 25 to 38 with compaction pressure. Consequently, at Bm of 50 mT and frequency of 100 kHz, the considerably low core loss of 67 kW/m3 was obtained. The low core loss and moderately high permeability of Fe–Si–B–Cr–C amorphous powder core across a wide frequency range indicate its potential for application in high frequency electronic components.

Year:

2024

Collaborators (8)

Masaki Mizuguchi

Nagoya University

JAPAN
View details

Satoshi Okamoto

Professor

Tohoku University

JAPAN
View details

Amit Kohn

Academic, Full Professor, Full Professor

Tel Aviv University

ISRAEL
View details

Koki Takanashi

Professor

Tohoku University

JAPAN
View details

Mai Phuong Nguyen

Assistant Professor

Tohoku University

JAPAN
View details

Mitsuharu Uemoto

Assistant Professor

Kobe University

JAPAN
View details

Saijian Ajia

Tohoku University

JAPAN
View details

Sho Muroga

Tohoku University

JAPAN
View details